Notice of Firmware Update for TX-NR807

A firmware update for the TX-NR807 network receiver is available through the unit’s network connection. The latest update includes the following content:

As of 1 October 2010
• Increases the stability of network operations;
• Improves the playback of some particular files.
As of 15 June 2010
• Stabilizes operation immediately after power is turned on (thereby avoiding problems of no sound output after the A/V receiver has been in Standby mode for an extended time with network control enabled).
As of 23 February 2010
• Improves operation with Windows 7 “Play To” by correcting the problem of lossy playback of DRM-protected 24 bit/96 kHz WMA Lossless files;
• Enhances S/N ratio during playback of 24 bit/96 kHz content via DLNA server;
• Reduces sound of speaker relay switching.
As of 19 November 2009
• Improves sound-level balance in Bi-amp mode;
• Reinforces the recovery capability of the update process.
As of 18 September 2009
• Adds Windows 7 compatibility and enables the “Play to” function for audio streaming from PCs running Windows 7;
• Enhances picture quality for an iPod/iPhone connected through the UP-A1.
Precautions for TX-NR807 Firmware Update
• The firmware update may fail if an external HDMI control signal is input during the update procedure. Please be sure to turn off the HDMI control function (RIHD) on your A/V receiver before starting the update.
How to turn off RIHD:

In the Main menu select “7. Hardware Setup”, then “7-4. HDMI”.
Set “HDMI Control” to OFF.

• Please read the update instructions carefully before beginning.

• The firmware update should take 15 to 25 minutes. Once the update begins, don’t turn off the power supply to the A/V receiver until it is time to restart it.

• Depending on the conditions of the network, a firmware update via a network may take more than one hour or even fail to finish. If the update is not completed within two hours, turn off the power supply by pushing the ON/STANDBY button and then try updating again from the beginning.

• Updating the firmware and adjusting the settings will be done automatically, but may take some time to complete. Please follow the procedures as instructed when you update. Note that the update may fail, or cause problems for your A/V receiver, if you do any of the following:

• Pull out the A/V receiver’s power cord;
• Interrupt the power supply to the A/V receiver (e.g. if the breaker is tripped or if there is an electrical outage);
• Insert or remove the LAN cable from a device in your network when updating over a network;
• Operate components connected to the A/V receiver via HDMI, such as a TV or a recording device.
If your A/V receiver is damaged for any of the reasons above, an Onkyo service center will repair the unit for a fee.
How to Install Firmware Update for TX-NR807

Click below for instructions on how to install the update.


Firmware update สำหรับรุ่น TX-NR807 Home Network Receiver สามารถอัพ Firmware ผ่านระบบเน็ตเวิร์ค (Network)

1.เพิ่มโปรแกรม Windows 7 หรือโปรแกรมเทียบเท่าระดับเดียวกัน และยังสามารถใช้ฟังก์ชั่น “Play to” สำหรับระบบเสียงออดิโอ
(Audio streaming) จาก PCs running Window 7
2.ปรับปรุงระบบภาพให้มีคุณภาพดียิ่งขึ้น สำหรับการใช้งานผ่าน iPod/iPhone ผ่าน iPod Docking รุ่น UP-A1

ทาง เราหวังเป็นอย่างยิ่งว่า หลังจากการปรับปรุง/อัพ Firmware จะทำให้คุณรู้สึกสุนทรีกับภาพและเสียง จากเครื่องเสียง ONKYO
Network Receiver ยิ่งขึ้นกดด้านล่างลิงค์ด้านล่าง เพื่อรับทราบวิธีการใช้และคำแนะนำการติดตั้งหรืออัพเดรต Firmware